Synergy Configuration Board "SYN_HMI_BD" R7FS7G27H2A01CBD part_number: R7FS7G27H2A01CBD rom_size_bytes: 4194304 ram_size_bytes: 655360 data_flash_size_bytes: 65536 package_style: BGA package_pins: 224 S7G2 series: 7 S7G2 Family OFS0 register settings: Select fields below IWDT Start Mode: IWDT is Disabled IWDT Timeout Period: 2048 cycles IWDT Dedicated Clock Frequency Divisor: 128 IWDT Window End Position: 0% (no window end position) IWDT Window Start Position: 100% (no window start position) IWDT Reset Interrupt Request Select: Reset is enabled IWDT Stop Control: Stop counting when in Sleep, Snooze mode, Software Standby, or Deep Software Standby mode WDT Start Mode Select: Stop WDT after a reset (register-start mode) WDT Timeout Period: 16384 cycles WDT Clock Frequency Division Ratio: 128 WDT Window End Position: 0% (no window end position) WDT Window Start Position: 100% (no window start position) WDT Reset Interrupt Request: Reset WDT Stop Control: Stop counting when entering Sleep mode OFS1 register settings: Select fields below Voltage Detection 0 Circuit Start: Voltage monitor 0 reset is disabled after reset Voltage Detection 0 Level: 2.80 V HOCO OScillation Enable: HOCO oscillation is disabled after reset Synergy Common Main stack size (bytes): 0x1000 Process stack size (bytes): 0 Heap size (bytes) - A minimum of 4K (0x1000) is required if standard library functions are to be used.: 0x10000 MCU Vcc (mV): 3300 Parameter checking: Enabled Assert Failures: Return SSP_ERR_ASSERTION Error Log: No Error Log ID code 1: 0xFFFFFFFF ID code 2: 0xFFFFFFFF ID code 3: 0xFFFFFFFF ID code 4: 0xFFFFFFFF Clocks XTAL 24000000Hz PLL Src: XTAL HOCO 20MHz PLL Div /2 PLL Mul x20.0 Clock Src: PLL ICLK Div /1 PCLKA Div /2 PCLKB Div /4 PCLKC Div /4 PCLKD Div /2 SDCLKout On BCLK Div /2 BCK/2 UCLK Div /5 FCLK Div /4 Pin Configurations SYN_HMI_BD.pincfg -> g_bsp_pin_cfg AVCC0 P8 ADC_AVCC0 - - - - - - - AVCCUSBHS H13 USBHS0_AVCCUSBHS - - - - - - - AVSS0 N9 ADC_AVSS0 - - - - - - - AVSSUSBHS G14 USBHS0_AVSSUSBHS - - - - - - - P000 R12 - - - - Disabled - - "ADC0: AN00; CMP0: IVCMP2; IRQ0: IRQ06" P001 P11 GPIO GPIO1 - IRQ7-DS "Input mode" - - "ADC0: AN01; CMP0: IVCMP2; IRQ0: IRQ07" P002 N12 - - - - Disabled - - "ADC0: AN02; CMP0: IVCMP2; IRQ0: IRQ08" P003 L10 - - - - Disabled - - "ADC0: PGAVSS0" P004 M11 - - - - Disabled - - "ADC1: AN00; CMP0: IVCMP2; IRQ0: IRQ09" P005 R11 - - - - Disabled - - "ADC1: AN01; CMP0: IVCMP2; IRQ0: IRQ10" P006 P10 GPIO GPIO2 - IRQ11-DS "Input mode" - - "ADC1: AN02; CMP0: IVCMP2; IRQ0: IRQ11" P007 L9 - - - - Disabled - - "ADC1: PGAVSS0" P008 N11 - - - - Disabled - - "ADC0: AN03; IRQ0: IRQ12" P009 R10 GPIO GPIO3 - IRQ13-DS "Input mode" - None "ADC0: AN04; IRQ0: IRQ13" P010 M10 GPIO GPIO14 - IRQ14-DS "Input mode" - None "ADC1: AN03; IRQ0: IRQ14" P011 N10 GPIO GPIO4 - IRQ15-DS "Input mode" - None "ADC1: AN04; IRQ0: IRQ15" P014 M9 - - - - Disabled - - "ADC0: AN05; ADC1: AN05; CMP0: IVREF3; DAC120: DA" P015 M8 - - - - Disabled - - "ADC0: AN06; ADC1: AN06; CMP0: IVCMP1; DAC121: DA; IRQ0: IRQ13" P100 R1 BUS0_D0_DQ0 External_Memory_Interface_D00__DQ00 High None "Peripheral mode" CMOS None "AGT0: AGTIO; BUS0: D0_DQ0; GLCDC0: LCD_EXTCLK; IIC1: SCL; IRQ0: IRQ02; KINT0: KRM0; POEG0: GTETRG; SCI0: RXD_MISO; SCI0: SCL; SCI1: SCK; SPI0: MISO" P101 P1 BUS0_D1_DQ1 External_Memory_Interface_D01__DQ01 High None "Peripheral mode" CMOS None "AGT0: AGTEE; BUS0: D1_DQ1; GLCDC0: LCD_CLK; IIC1: SDA; IRQ0: IRQ01; KINT0: KRM1; POEG1: GTETRG; SCI0: SDA; SCI0: TXD_MOSI; SCI1: CTS_RTS_SS; SPI0: MOSI" P102 N1 BUS0_D2_DQ2 External_Memory_Interface_D02__DQ02 High - "Peripheral mode" CMOS None "ADC0: ADTRG; AGT0: AGTO; BUS0: D2_DQ2; GLCDC0: LCD_TCON0; GPT2: GTIOCB; KINT0: KRM2; OPS0: GTOWLO; SCI0: SCK; SPI0: RSPCK" P103 N2 BUS0_D3_DQ3 External_Memory_Interface_D03__DQ03 High - "Peripheral mode" CMOS None "BUS0: D3_DQ3; GLCDC0: LCD_TCON1; GPT2: GTIOCA; KINT0: KRM3; OPS0: GTOWUP; SCI0: CTS_RTS_SS; SPI0: SSL0" P104 N3 BUS0_D4_DQ4 External_Memory_Interface_D04__DQ04 High None "Peripheral mode" CMOS None "BUS0: D4_DQ4; GLCDC0: LCD_TCON2; IRQ0: IRQ01; KINT0: KRM4; POEG1: GTETRG; SCI8: RXD_MISO; SCI8: SCL; SPI0: SSL1" P105 M3 BUS0_D5_DQ5 External_Memory_Interface_D05__DQ05 High None "Peripheral mode" CMOS None "BUS0: D5_DQ5; GLCDC0: LCD_TCON3; IRQ0: IRQ00; KINT0: KRM5; POEG0: GTETRG; SCI8: SDA; SCI8: TXD_MOSI; SPI0: SSL2" P106 L4 BUS0_D6_DQ6 External_Memory_Interface_D06__DQ06 High - "Peripheral mode" CMOS None "BUS0: D6_DQ6; GLCDC0: LCD_DATA00; GPT8: GTIOCB; KINT0: KRM6; SCI8: SCK; SPI0: SSL3" P107 K4 BUS0_D7_DQ7 External_Memory_Interface_D07__DQ07 High - "Peripheral mode" CMOS None "BUS0: D7_DQ7; GLCDC0: LCD_DATA01; GPT8: GTIOCA; KINT0: KRM7; SCI8: CTS_RTS_SS" P108 B2 DEBUG0_TMS JTAG_TMS Low - "Peripheral mode" CMOS None "DEBUG0: SWDIO; DEBUG0: TMS; GPT0: GTIOCB; SCI9: CTS_RTS_SS; SPI1: SSL0" P109 B1 DEBUG0_TDO JTAG_TDO Low - "Peripheral mode" CMOS None "CAN1: CTX; CGC0: CLKOUT; DEBUG0: SWO; DEBUG0: TDO; GPT1: GTIOCA; OPS0: GTOVUP; SCI9: SDA; SCI9: TXD_MOSI; SPI1: MOSI" P110 C2 DEBUG0_TDI JTAG_TDI Low None "Peripheral mode" CMOS None "CAN1: CRX; CMP0: VCOUT; DEBUG0: TDI; GPT1: GTIOCB; IRQ0: IRQ03; OPS0: GTOVLO; SCI2: CTS_RTS_SS; SCI9: RXD_MISO; SCI9: SCL; SPI1: MISO" P111 C1 BUS0_A05 External_Memory_Interface_A05 High None "Peripheral mode" CMOS None "BUS0: A05; GLCDC0: LCD_DATA12; GPT3: GTIOCA; IRQ0: IRQ04; SCI2: SCK; SCI9: SCK; SPI1: RSPCK" P112 C3 BUS0_A04 External_Memory_Interface_A04 High - "Peripheral mode" CMOS None "BUS0: A04; GLCDC0: LCD_DATA11; GPT3: GTIOCB; SCI2: SDA; SCI2: TXD_MOSI; SSI0: SSISCK" P113 D3 BUS0_A03 External_Memory_Interface_A03 High - "Peripheral mode" CMOS None "BUS0: A03; GLCDC0: LCD_DATA10; SCI2: RXD_MISO; SCI2: SCL; SSI0: SSIWS" P114 E4 BUS0_A02 External_Memory_Interface_A02 High - "Peripheral mode" CMOS None "BUS0: A02; GLCDC0: LCD_DATA09; SSI0: SSIRXD" P115 E3 BUS0_A01 External_Memory_Interface_A01 High - "Peripheral mode" CMOS None "BUS0: A01; GLCDC0: LCD_DATA08; SSI0: SSITXD" P200 B8 - - - - Disabled - - "IRQ0: NMI" P201 C8 - - - - Disabled - - - P202 A12 SCI9_RXD_MISO SCI9_RXD9_SCL9_MISO9 Low None "Peripheral mode" CMOS None "BUS0: WR1_BC1; CAN0: CRX; ETHERC0: ERXD2; GLCDC0: LCD_TCON3; GPT5: GTIOCB; IRQ0: IRQ03; SCI2: SCK; SCI9: RXD_MISO; SCI9: SCL; SDHI0: DAT6; SPI1: MISO" P203 B12 SCI9_TXD_MOSI SCI9_TXD9_SDA9_MOSI9 Low None "Peripheral mode" CMOS None "BUS0: A19; CAN0: CTX; CTSU0: TSCAP; ETHERC0: COL; GPT5: GTIOCA; IRQ0: IRQ02; SCI2: CTS_RTS_SS; SCI9: SDA; SCI9: TXD_MOSI; SDHI0: DAT5; SPI1: MOSI" P204 D11 CTSU0_TS00 Cap_Touch_Sensing_Unit_TS00 Low - "Peripheral mode" CMOS None "AGT1: AGTIO; BUS0: A18; CAC0: CACREF; CTSU0: TS00; ETHERC0: RX_DV; GPT4: GTIOCB; IIC0: SCL; OPS0: GTIW; SCI4: SCK; SCI9: SCK; SDHI0: DAT4; SPI1: RSPCK; SSI1: SSISCK; USBFS0: OVRCURB" P205 C12 CTSU0_TSCAP CAP_TOUCH_SENSING_UNIT_TSCAP Low None "Peripheral mode" CMOS None "AGT1: AGTO; BUS0: A16; CGC0: CLKOUT; CTSU0: TSCAP; ETHERC0: WOL; ETHERC0: WOL; GPT4: GTIOCA; IIC1: SCL; IRQ0: IRQ01; OPS0: GTIV; SCI4: SDA; SCI4: TXD_MOSI; SCI9: CTS_RTS_SS; SDHI0: DAT3; SPI1: SSL0; SSI1: SSIWS; USBFS0: OVRCURA" P206 G9 CTSU0_TS01 Cap_Touch_Sensing_Unit_TS01 Low None "Peripheral mode" CMOS None "BUS0: WAIT; CTSU0: TS01; ETHERC0: LINKSTA; ETHERC0: LINKSTA; IIC1: SDA; IRQ0: IRQ00; OPS0: GTIU; SCI4: RXD_MISO; SCI4: SCL; SDHI0: DAT2; SPI1: SSL1; SSI1: SSIDATA; USBFS0: VBUSEN" P207 C13 CTSU0_TS02 Cap_Touch_Sensing_Unit_TS02 Low - "Peripheral mode" CMOS None "BUS0: A17; CTSU0: TS02; SPI1: SSL2" P212 H15 - - - - Disabled - - "AGT1: AGTEE; CGC0: EXTAL; IRQ0: IRQ03; POEG3: GTETRG; SCI1: RXD_MISO; SCI1: SCL" P213 H14 - - - - Disabled - - "ADC1: ADTRG; CGC0: XTAL; IRQ0: IRQ02; POEG2: GTETRG; SCI1: SDA; SCI1: TXD_MOSI" P300 F5 DEBUG0_TCK JTAG_TCK Low - "Peripheral mode" CMOS None "DEBUG0: SWCLK; DEBUG0: TCK; GPT0: GTIOCA; SPI1: SSL1" P301 B3 BUS0_A06 External_Memory_Interface_A06 High None "Peripheral mode" CMOS None "BUS0: A06; GLCDC0: LCD_DATA13; GPT4: GTIOCB; IRQ0: IRQ06; OPS0: GTOULO; SCI2: RXD_MISO; SCI2: SCL; SPI1: SSL2" P302 A2 BUS0_A07 External_Memory_Interface_A07 High None "Peripheral mode" CMOS None "BUS0: A07; GLCDC0: LCD_DATA14; GPT4: GTIOCA; IRQ0: IRQ05; OPS0: GTOUUP; SCI2: SDA; SCI2: TXD_MOSI; SPI1: SSL3" P303 A3 BUS0_A08 External_Memory_Interface_A08 High - "Peripheral mode" CMOS None "BUS0: A08; GLCDC0: LCD_DATA15; GPT7: GTIOCB" P304 C4 BUS0_A09 External_Memory_Interface_A09 High None "Peripheral mode" CMOS None "BUS0: A09; GLCDC0: LCD_DATA16; GPT7: GTIOCA; IRQ0: IRQ09; SCI6: RXD_MISO; SCI6: SCL" P305 D4 BUS0_A10 External_Memory_Interface_A10 High None "Peripheral mode" CMOS None "BUS0: A10; GLCDC0: LCD_DATA17; IRQ0: IRQ08; SCI6: SDA; SCI6: TXD_MOSI" P306 D5 BUS0_A11 External_Memory_Interface_A11 High - "Peripheral mode" CMOS None "BUS0: A11; GLCDC0: LCD_DATA18; SCI6: SCK" P307 D6 BUS0_A12 External_Memory_Interface_A12 High - "Peripheral mode" CMOS None "BUS0: A12; GLCDC0: LCD_DATA19; SCI6: CTS_RTS_SS" P308 D7 BUS0_A13 External_Memory_Interface_A13 High - "Peripheral mode" CMOS None "BUS0: A13; GLCDC0: LCD_DATA20" P309 C5 BUS0_A14 External_Memory_Interface_A14 High - "Peripheral mode" CMOS None "BUS0: A14; GLCDC0: LCD_DATA21" P310 C6 BUS0_A15 External_Memory_Interface_A15 High - "Peripheral mode" CMOS None "BUS0: A15; GLCDC0: LCD_DATA22" P311 C7 BUS0_CS2_RAS External_Memory_Interface_CS2__RAS High - "Peripheral mode" CMOS None "BUS0: CS2_RAS; GLCDC0: LCD_DATA23" P312 B6 BUS0_CS3_CAS External_Memory_Interface_CS3__CAS High - "Peripheral mode" CMOS None "BUS0: CS3_CAS" P313 E10 GLCDC0_LCD_TCON2 GLCD_Controller__Pin_Option_B_LCD_TCON2_B High - "Peripheral mode" CMOS None "BUS0: A20; ETHERC0: ERXD3; GLCDC0: LCD_TCON2; SDHI0: DAT7" P314 F9 GLCDC0_LCD_TCON1 GLCD_Controller__Pin_Option_B_LCD_TCON1_B High - "Peripheral mode" CMOS None "BUS0: A21; GLCDC0: LCD_TCON1" P315 C11 GLCDC0_LCD_TCON0 GLCD_Controller__Pin_Option_B_LCD_TCON0_B High - "Peripheral mode" CMOS None "BUS0: A22; GLCDC0: LCD_TCON0" P400 N13 - - - - Disabled - - "ADC1: ADTRG; ETHERC1: TX_CLK; GPT6: GTIOCA; IIC0: SCL; IRQ0: IRQ00; SCI4: SCK; SCI7: SCK; SSI: AUDIO_CLK" P401 P15 - - - - Disabled - - "CAN0: CTX; ETHERC0: MDC; ETHERC0: MDC; GPT6: GTIOCB; IIC0: SDA; IRQ0: IRQ05; POEG0: GTETRG; SCI4: CTS_RTS_SS; SCI7: SDA; SCI7: TXD_MOSI" P402 N14 - - - - Disabled - - "AGT0: AGTIO; AGT1: AGTIO; CAN0: CRX; ETHERC0: MDIO; ETHERC0: MDIO; IRQ0: IRQ04; RTC0: RTCIC0; SCI7: RXD_MISO; SCI7: SCL" P403 N15 RMII_MDC Ethernet_Controller_1_RMII_ET1_MDC Medium - "Peripheral mode" CMOS None "AGT0: AGTIO; AGT1: AGTIO; ETHERC1: MDC; ETHERC1: MDC; GPT3: GTIOCA; PDC0: PIXD7; RTC0: RTCIC1; SCI7: CTS_RTS_SS; SSI0: SSISCK" P404 K10 RMII_MDIO Ethernet_Controller_1_RMII_ET1_MDIO Medium - "Peripheral mode" CMOS None "ETHERC1: MDIO; ETHERC1: MDIO; GPT3: GTIOCB; PDC0: PIXD6; RTC0: RTCIC2; SSI0: SSIWS" P405 M13 RMII_TXD_EN Ethernet_Controller_1_RMII_RMII1_TXD_EN High - "Peripheral mode" CMOS None "ETHERC1: TX_EN; ETHERC1: TXD_EN; GPT1: GTIOCA; PDC0: PIXD5; SSI0: SSITXD" P406 J9 RMII_TXD1 Ethernet_Controller_1_RMII_RMII1_TXD1 High - "Peripheral mode" CMOS None "ETHERC1: RX_ER; ETHERC1: TXD1; GPT1: GTIOCB; PDC0: PIXD4; SSI0: SSIRXD" P407 A15 - - - - Disabled - - "ADC0: ADTRG; CTSU0: TS03; ETHERC0: EXOUT; ETHERC0: EXOUT; IIC0: SDA; RTC0: RTCOUT; SCI4: CTS_RTS_SS; SPI1: SSL3; USBFS0: VBUS" P408 B15 - - - - Disabled - - "CTSU0: TS04; ETHERC0: CRS; ETHERC0: CRS_DV; GPT10: GTIOCB; IRQ0: IRQ07; OPS0: GTOWLO; SCI3: RXD_MISO; SCI3: SCL; USBFS0: ID; USBHS0: ID" P409 C14 - - - - Disabled - - "CTSU0: TS05; ETHERC0: RX_CLK; ETHERC0: RX_ER; GPT10: GTIOCA; IRQ0: IRQ06; OPS0: GTOWUP; SCI3: SDA; SCI3: TXD_MOSI; USBFS0: EXICEN; USBHS0: EXICEN" P410 C15 - - - - Disabled - - "AGT1: AGTOB; CTSU0: TS06; ETHERC0: ERXD0; ETHERC0: RXD1; GPT9: GTIOCB; IRQ0: IRQ05; OPS0: GTOVLO; SCI0: RXD_MISO; SCI0: SCL; SCI3: SCK; SDHI0: DAT1; SPI0: MISO" P411 D14 - - - - Disabled - - "AGT1: AGTOA; CTSU0: TS07; ETHERC0: ERXD1; ETHERC0: RXD0; GPT9: GTIOCA; IRQ0: IRQ04; OPS0: GTOVUP; SCI0: SDA; SCI0: TXD_MOSI; SCI3: CTS_RTS_SS; SDHI0: DAT0; SPI0: MOSI" P412 D13 - - - - Disabled - - "CTSU0: TS08; ETHERC0: ETXD0; ETHERC0: REF50CK; OPS0: GTOULO; SCI0: SCK; SDHI0: CMD; SPI0: RSPCK" P413 D12 - - - - Disabled - - "CTSU0: TS09; ETHERC0: ETXD1; ETHERC0: TXD0; OPS0: GTOUUP; SCI0: CTS_RTS_SS; SDHI0: CLK; SPI0: SSL0" P414 E11 - - - - Disabled - - "CTSU0: TS10; ETHERC0: RX_ER; ETHERC0: TXD1; SDHI0: WP; SPI0: SSL1" P415 E14 - - - - Disabled - - "CTSU0: TS11; ETHERC0: TX_EN; ETHERC0: TXD_EN; SPI0: SSL2" P500 R4 QSPI0_QSPCLK Quad_SPI_QSPCLK High - "Peripheral mode" CMOS None "ADC0: AN16; AGT0: AGTOA; CMP0: IVREF0; GPT11: GTIOCA; OPS0: GTIU; QSPI0: QSPCLK; SDHI1: CLK; USBFS0: VBUSEN" P501 N4 QSPI0_QSSL Quad_SPI_QSSL High None "Peripheral mode" CMOS None "ADC1: AN16; AGT0: AGTOB; CMP0: IVREF1; GPT11: GTIOCB; IRQ0: IRQ11; OPS0: GTIV; QSPI0: QSSL; SCI5: SDA; SCI5: TXD_MOSI; SDHI1: CMD; USBFS0: OVRCURA" P502 N5 QSPI0_QIO0 Quad_SPI_QIO0 High None "Peripheral mode" CMOS None "ADC0: AN17; CMP0: IVCMP0; GPT12: GTIOCA; IRQ0: IRQ12; OPS0: GTIW; QSPI0: QIO0; SCI5: RXD_MISO; SCI5: SCL; SDHI1: DAT0; USBFS0: OVRCURB" P503 P5 QSPI0_QIO1 Quad_SPI_QIO1 High - "Peripheral mode" CMOS None "ADC1: AN17; GPT12: GTIOCB; POEG2: GTETRG; QSPI0: QIO1; SCI5: SCK; SCI6: CTS_RTS_SS; SDHI1: DAT1; USBFS0: EXICEN" P504 R5 QSPI0_QIO2 Quad_SPI_QIO2 High - "Peripheral mode" CMOS None "ADC0: AN18; GPT13: GTIOCA; POEG3: GTETRG; QSPI0: QIO2; SCI5: CTS_RTS_SS; SCI6: SCK; SDHI1: DAT2; USBFS0: ID" P505 M5 QSPI0_QIO3 Quad_SPI_QIO3 High None "Peripheral mode" CMOS None "ADC1: AN18; GPT13: GTIOCB; IRQ0: IRQ14; QSPI0: QIO3; SCI6: RXD_MISO; SCI6: SCL; SDHI1: DAT3" P506 M6 - - - - Disabled - - "ADC0: AN19; IRQ0: IRQ15; SCI6: SDA; SCI6: TXD_MOSI; SDHI1: CD" P507 N6 - - - - Disabled - - "ADC1: AN19; SCI5: CTS_RTS_SS; SDHI1: WP" P508 M7 - - - - Disabled - - "ADC0: AN20; SCI5: SCK" P509 P6 - - - - Disabled - - "ADC1: AN20; SCI5: SDA; SCI5: TXD_MOSI" P510 N7 - - - - Disabled - - "ADC0: AN21; SCI5: RXD_MISO; SCI5: SCL" P511 R15 - - - - Disabled - - "CAN1: CRX; ETHERC1: TX_ER; GPT0: GTIOCB; IIC2: SDA; IRQ0: IRQ15; PDC0: PCKO; SCI4: RXD_MISO; SCI4: SCL" P512 R14 - - - - Disabled - - "CAN1: CTX; ETHERC1: ETXD2; GPT0: GTIOCA; IIC2: SCL; IRQ0: IRQ14; PDC0: VSYNC; SCI4: SDA; SCI4: TXD_MOSI" P513 P13 GLCDC0_LCD_DATA16 GLCD_Controller__Pin_Option_B_LCD_DATA16_B High - "Peripheral mode" CMOS None "ETHERC1: ETXD3; GLCDC0: LCD_DATA16" P514 P14 GPIO GPIO5 Low - "Output mode (Initial Low)" CMOS None "POEG1: GTETRG" P515 K9 GPIO GPIO6 Low - "Output mode (Initial Low)" CMOS None - P600 L3 - - - - Disabled - - "BUS0: RD; GLCDC0: LCD_DATA02" P601 L2 BUS0_WR_WR0_DQM0 External_Memory_Interface_WR_WR0__DQM0 High - "Peripheral mode" CMOS None "BUS0: WR_WR0_DQM0; GLCDC0: LCD_DATA03" P602 L1 BUS0_BCLK_SDCLK External_Memory_Interface_EBCLK__SDCLK High - "Peripheral mode" CMOS None "BUS0: BCLK_SDCLK; GLCDC0: LCD_DATA04" P603 K3 BUS0_D13_DQ13 External_Memory_Interface_D13__DQ13 High - "Peripheral mode" CMOS None "BUS0: D13_DQ13" P604 K2 BUS0_D12_DQ12 External_Memory_Interface_D12__DQ12 High - "Peripheral mode" CMOS None "BUS0: D12_DQ12" P605 K1 BUS0_D11_DQ11 External_Memory_Interface_D11__DQ11 High - "Peripheral mode" CMOS None "BUS0: D11_DQ11" P606 K6 GLCDC0_LCD_DATA03 GLCD_Controller__Pin_Option_B_LCD_DATA03_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA03" P607 K5 GLCDC0_LCD_DATA04 GLCD_Controller__Pin_Option_B_LCD_DATA04_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA04" P608 F4 BUS0_A00_BC0_DQM1 External_Memory_Interface_A00_BC0__A00_DQM1 High - "Peripheral mode" CMOS None "BUS0: A00_BC0_DQM1; GLCDC0: LCD_DATA07" P609 G4 BUS0_CS1_CKE External_Memory_Interface_CS1__CKE High - "Peripheral mode" CMOS None "BUS0: CS1_CKE; GLCDC0: LCD_DATA06" P610 E1 BUS0_CS0_WE External_Memory_Interface_CS0__WE High - "Peripheral mode" CMOS None "BUS0: CS0_WE; GLCDC0: LCD_DATA05" P611 E2 BUS0_SDCS External_Memory_Interface_SDCS High - "Peripheral mode" CMOS None "BUS0: SDCS" P612 F2 BUS0_D8_DQ8 External_Memory_Interface_D08__DQ08 High - "Peripheral mode" CMOS None "BUS0: D8_DQ8" P613 F3 BUS0_D9_DQ9 External_Memory_Interface_D09__DQ09 High - "Peripheral mode" CMOS None "BUS0: D9_DQ9" P614 F1 BUS0_D10_DQ10 External_Memory_Interface_D10__DQ10 High - "Peripheral mode" CMOS None "BUS0: D10_DQ10" P615 G8 GLCDC0_LCD_DATA10 GLCD_Controller__Pin_Option_B_LCD_DATA10_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA10" P700 M14 RMII_TXD0 Ethernet_Controller_1_RMII_RMII1_TXD0 High - "Peripheral mode" CMOS None "ETHERC1: ETXD1; ETHERC1: TXD0; GPT5: GTIOCA; PDC0: PIXD3" P701 M15 RMII_REF50CK Ethernet_Controller_1_RMII_REF50CK1 High - "Peripheral mode" CMOS None "ETHERC1: ETXD0; ETHERC1: REF50CK; GPT5: GTIOCB; PDC0: PIXD2" P702 K11 RMII_RXD0 Ethernet_Controller_1_RMII_RMII1_RXD0 High - "Peripheral mode" CMOS None "ETHERC1: ERXD1; ETHERC1: RXD0; GPT6: GTIOCA; PDC0: PIXD1" P703 J8 RMII_RXD1 Ethernet_Controller_1_RMII_RMII1_RXD1 High - "Peripheral mode" CMOS None "ETHERC1: ERXD0; ETHERC1: RXD1; GPT6: GTIOCB; PDC0: PIXD0" P704 J10 RMII_RX_ER Ethernet_Controller_1_RMII_RMII1_RX_ER High - "Peripheral mode" CMOS None "ETHERC1: RX_CLK; ETHERC1: RX_ER; PDC0: HSYNC" P705 L13 RMII_CRS_DV Ethernet_Controller_1_RMII_RMII1_CRS_DV High - "Peripheral mode" CMOS None "ETHERC1: CRS; ETHERC1: CRS_DV; PDC0: PIXCLK" P706 L14 GPIO GPIO7 Low None "Output mode (Initial Low)" CMOS None "IRQ0: IRQ07; SCI3: RXD_MISO; SCI3: SCL; USBHS0: OVRCURB" P707 L15 - - - - Disabled - - "IRQ0: IRQ08; SCI3: SDA; SCI3: TXD_MOSI; USBHS0: OVRCURA" P708 D15 - - - - Disabled - - "CAC0: CACREF; CTSU0: TS12; ETHERC0: ETXD3; IRQ0: IRQ11; SCI1: RXD_MISO; SCI1: SCL; SPI0: SSL3" P709 E13 - - - - Disabled - - "CTSU0: TS13; ETHERC0: ETXD2; IRQ0: IRQ10; SCI1: SDA; SCI1: TXD_MOSI" P710 F10 GPIO GPIO9 Low - "Output mode (Initial Low)" CMOS None "CTSU0: TS14; ETHERC0: TX_ER; SCI1: SCK" P711 E12 GPIO GPIO8 Low - "Output mode (Initial Low)" CMOS None "CTSU0: TS15; ETHERC0: TX_CLK; SCI1: CTS_RTS_SS" P712 F11 GPT2_GTIOCB GPT02__Pin_Option_B_GTIOC2B_B Low - "Peripheral mode" CMOS None "CTSU0: TS16; GPT2: GTIOCB" P713 G10 - - - - Disabled - - "CTSU0: TS17; ETHERC1: EXOUT; ETHERC1: EXOUT; GPT2: GTIOCA" P800 P2 BUS0_D14_DQ14 External_Memory_Interface_D14__DQ14 High - "Peripheral mode" CMOS None "BUS0: D14_DQ14" P801 R2 BUS0_D15_DQ15 External_Memory_Interface_D15__DQ15 High - "Peripheral mode" CMOS None "BUS0: D15_DQ15; SDHI1: DAT4" P802 R3 GLCDC0_LCD_DATA02 GLCD_Controller__Pin_Option_B_LCD_DATA02_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA02; SDHI1: DAT5" P803 P4 GLCDC0_LCD_DATA01 GLCD_Controller__Pin_Option_B_LCD_DATA01_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA01; SDHI1: DAT6" P804 M4 GLCDC0_LCD_DATA00 GLCD_Controller__Pin_Option_B_LCD_DATA00_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA00; SDHI1: DAT7" P805 R13 GLCDC0_LCD_DATA17 GLCD_Controller__Pin_Option_B_LCD_DATA17_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA17" P806 M12 GPIO GPIO15 Low - "Output mode (Initial Low)" CMOS None "GLCDC0: LCD_EXTCLK" P807 P12 GPIO GPIO10 Low - "Output mode (Initial Low)" CMOS None - P808 K7 GPIO GPIO11 Low - "Output mode (Initial Low)" CMOS None - P809 K8 GPIO GPIO12 Low - "Output mode (Initial Low)" CMOS None - P810 P3 GPIO GPIO13 Low - "Output mode (Initial Low)" CMOS None - P811 L5 - - - - Disabled - - "CAN0: CTX" P812 L6 - - - - Disabled - - "CAN0: CRX" P813 G1 - - - - Disabled - - "GPT9: GTIOCB; TRACE0: TDATA3" P900 E9 GLCDC0_LCD_CLK GLCD_Controller__Pin_Option_B_LCD_CLK_B High - "Peripheral mode" CMOS None "BUS0: A23; GLCDC0: LCD_CLK" P901 B11 GLCDC0_LCD_DATA15 GLCD_Controller__Pin_Option_B_LCD_DATA15_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA15" P902 A11 GLCDC0_LCD_DATA23 GLCD_Controller__Pin_Option_B_LCD_DATA23_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA23" P903 D9 - - - - Disabled - - "GPT7: GTIOCA; SDHI0: CD" P904 C9 - - - - Disabled - - "GPT7: GTIOCB" P905 A6 GLCDC0_LCD_DATA11 GLCD_Controller__Pin_Option_B_LCD_DATA11_B High - "Peripheral mode" CMOS None "BUS0: CS4; GLCDC0: LCD_DATA11" P906 F6 GLCDC0_LCD_DATA12 GLCD_Controller__Pin_Option_B_LCD_DATA12_B High - "Peripheral mode" CMOS None "BUS0: CS5; GLCDC0: LCD_DATA12" P907 F7 GLCDC0_LCD_DATA13 GLCD_Controller__Pin_Option_B_LCD_DATA13_B High - "Peripheral mode" CMOS None "BUS0: CS6; GLCDC0: LCD_DATA13" P908 E7 GLCDC0_LCD_DATA14 GLCD_Controller__Pin_Option_B_LCD_DATA14_B High - "Peripheral mode" CMOS None "BUS0: CS7; GLCDC0: LCD_DATA14" P909 E8 GLCDC0_LCD_DATA21 GLCD_Controller__Pin_Option_B_LCD_DATA21_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA21" P910 D8 GLCDC0_LCD_DATA22 GLCD_Controller__Pin_Option_B_LCD_DATA22_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA22" P911 A7 - - - - Disabled - - "GPT8: GTIOCB" P912 B7 - - - - Disabled - - "GPT8: GTIOCA" P913 H8 - - - - Disabled - - - P914 E5 GLCDC0_LCD_DATA19 GLCD_Controller__Pin_Option_B_LCD_DATA19_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA19" P915 E6 GLCDC0_LCD_DATA20 GLCD_Controller__Pin_Option_B_LCD_DATA20_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA20" PA00 J7 GLCDC0_LCD_DATA05 GLCD_Controller__Pin_Option_B_LCD_DATA05_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA05" PA01 J6 GLCDC0_LCD_DATA06 GLCD_Controller__Pin_Option_B_LCD_DATA06_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA06" PA02 H6 SCI7_TXD_MOSI SCI7_TXD7_SDA7_MOSI7 Low None "Peripheral mode" "n-ch open drain" None "IRQ0: IRQ10; SCI7: SDA; SCI7: TXD_MOSI" PA03 J5 SCI7_RXD_MISO SCI7_RXD7_SCL7_MISO7 High None "Peripheral mode" "n-ch open drain" None "IRQ0: IRQ09; SCI7: RXD_MISO; SCI7: SCL" PA04 J4 - - - - Disabled - - "GPT11: GTIOCB; SCI7: SCK" PA05 J3 - - - - Disabled - - "GPT11: GTIOCA; SCI7: CTS_RTS_SS" PA06 J2 - - - - Disabled - - "GPT10: GTIOCB" PA07 J1 - - - - Disabled - - "GPT10: GTIOCA" PA08 G7 GLCDC0_LCD_DATA09 GLCD_Controller__Pin_Option_B_LCD_DATA09_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA09" PA09 H4 GLCDC0_LCD_DATA08 GLCD_Controller__Pin_Option_B_LCD_DATA08_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA08" PA10 H5 GLCDC0_LCD_DATA07 GLCD_Controller__Pin_Option_B_LCD_DATA07_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA07" PA11 G6 GLCDC0_LCD_DATA18 GLCD_Controller__Pin_Option_B_LCD_DATA18_B High - "Peripheral mode" CMOS None "GLCDC0: LCD_DATA18" PA12 G5 - - - - Disabled - - "TRACE0: TCLK" PA13 H7 - - - - Disabled - - "TRACE0: TDATA0" PA14 G3 - - - - Disabled - - "TRACE0: TDATA1" PA15 G2 - - - - Disabled - - "GPT9: GTIOCA; TRACE0: TDATA2" PB00 H9 - - - - Disabled - - "SCI3: SCK; USBHS0: VBUSEN" PB01 K13 - - - - Disabled - - "SCI3: CTS_RTS_SS; USBHS0: VBUS" PB02 J11 SCI8_CTS_RTS_SS SCI8_CTS8_RTS8_SS8 Medium - "Peripheral mode" CMOS None "ETHERC1: RX_DV; SCI8: CTS_RTS_SS" PB03 K12 SCI8_SCK SCI8_SCK8 High - "Peripheral mode" CMOS None "ETHERC1: COL; SCI8: SCK" PB04 H10 SCI8_TXD_MOSI SCI8_TXD8_SDA8_MOSI8 Medium None "Peripheral mode" CMOS "input pull-up" "ETHERC1: ERXD2; IRQ0: IRQ12; SCI8: SDA; SCI8: TXD_MOSI" PB05 J12 SCI8_RXD_MISO SCI8_RXD8_SCL8_MISO8 Medium None "Peripheral mode" CMOS "input pull-up" "ETHERC1: ERXD3; IRQ0: IRQ13; SCI8: RXD_MISO; SCI8: SCL" PB06 H11 - - - - Disabled - - "ETHERC1: WOL; ETHERC1: WOL" PB07 G11 - - - - Disabled - - "ETHERC1: LINKSTA; ETHERC1: LINKSTA" PVSSUSBHS G15 USBHS0_PVSSUSBHS - - - - - - - RES F8 - - - - - - - - USBDM B14 USBFS0_USBDM - - - - - - - USBDP A14 USBFS0_USBDP - - - - - - - USBHSDM F15 USBHS0_USBHSDM - - - - - - - USBHSDP F14 USBHS0_USBHSDP - - - - - - - USBHSRREF G13 USBHS0_USBHSRREF - - - - - - - VBAT K14 - - - - - - - - VCC B4 - - - - - - - - VCC D10 - - - - - - - - VCC B5 - - - - - - - - VCC M2 - - - - - - - - VCC A8 - - - - - - - - VCC P7 - - - - - - - - VCC H12 - - - - - - - - VCC H3 - - - - - - - - VCC L7 - - - - - - - - VCC L12 - - - - - - - - VCC D1 - - - - - - - - VCCUSB A13 USBFS0_VCCUSB - - - - - - - VCCUSBHS F13 USBHS0_VCCUSBHS - - - - - - - VCL K15 - - - - - - - - VCL1 A10 - - - - - - - - VCL1 H1 - - - - - - - - VCL2 R6 - - - - - - - - VLO B9 - - - - - - - - VLO A9 - - - - - - - - VREFH R8 ADC_VREFH - - - - - - - VREFH0 R9 ADC_VREFH0 - - - - - - - VREFL N8 ADC_VREFL - - - - - - - VREFL0 P9 ADC_VREFL0 - - - - - - - VSS B10 - - - - - - - - VSS A4 - - - - - - - - VSS C10 - - - - - - - - VSS A5 - - - - - - - - VSS M1 - - - - - - - - VSS R7 - - - - - - - - VSS E15 - - - - - - - - VSS H2 - - - - - - - - VSS L8 - - - - - - - - VSS L11 - - - - - - - - VSS J13 - - - - - - - - VSS D2 - - - - - - - - VSS1USBHS F12 USBHS0_VSS1USBHS - - - - - - - VSS2USBHS G12 USBHS0_VSS2USBHS - - - - - - - VSSUSB B13 USBFS0_VSSUSB - - - - - - - XCIN J15 CGC0_XCIN - - - - - - - XCOUT J14 CGC0_XCOUT - - - - - - - Module "CGC Driver on r_cgc" Parameter Checking: Default (BSP) Main Oscillator Wait Time: 8163 cycles Main Oscillator Clock Source: Crystal or Resonator Oscillator Stop Detect: Enabled Subclock Drive: Standard (12.5pf) Low Voltage Mode: Disable Module "ELC Driver on r_elc" Parameter Checking: Default (BSP) Module "FMI Driver on r_fmi" Parameter Checking: Default (BSP) SSP MCU Information Symbol Name: g_fmi_data Part Number Mask: 0xFE00 Module "I/O Port Driver on r_ioport" Parameter Checking: Default (BSP) Module "Timer Driver on r_gpt" Parameter Checking: Default (BSP) Module "QSPI Driver on QSPI" Parameter Checking: Default (BSP) Module "External IRQ Driver on r_icu" Parameter Checking: Default (BSP) Module "Cap Touch Button Framework on sf_touch_ctsu_button" Parameter Checking: Default (BSP) Number of Buttons: 3 Short hold debounce multiplier: 1 Long hold debounce multiplier: 5 Stuck in debounce multiplier: 10 Multi touch enable: Disabled Enable stuck at condition detection: Disabled Module "GUIX on gx" Enable Synergy 2D Drawing Engine Support: Yes Enable Synergy JPEG Support: Yes Module "Touch Panel Framework on sf_touch_panel_i2c" Parameter Checking: Default (BSP) Module "Communications Framework on sf_uart_comms" Parameter Checking: Default (BSP) Read Input Queue Size (4-Byte Words): 15 Module "NetX Duo DHCP IPv4 Client" Internal thread priority: 3 Internal thread stack size (bytes): 4096 Timeout between DHCP messages processed (seconds): 1 Use BOOTP: Disable Send ARP probe: Disable ARP probe wait time (seconds): 1 Minimum ARP probe wait time (seconds): 1 Maximum ARP probe wait time (seconds): 2 ARP probe count: 2 Maximum retransmission timeout (seconds): 64 Minimum renew timeout (seconds): 60 Minimum retransmission timeout (seconds): 4 Client packet payload size (bytes): 592 Number of packets in internal packet pool: 5 Persistent client state: Disable Use application packet pool: Disable Maximum message size support: Disable DHCP options buffer size (bytes): 312 Maximum DHCP client state record on a interface: 1 Wait before restarting the configuration process (seconds): 10 HAL Instance "g_cgc CGC Driver on r_cgc" Name [Fixed]: g_cgc Instance "g_elc ELC Driver on r_elc" Name [Fixed]: g_elc Instance "g_fmi FMI Driver on r_fmi" Name: g_fmi Instance "g_ioport I/O Port Driver on r_ioport" Name [Fixed]: g_ioport Instance "g_touch_panel_polling_timer Timer Driver on r_gpt" Name: g_touch_panel_polling_timer Channel: 5 Mode: One Shot Period Value: 50 Period Unit: Milliseconds Duty Cycle Value: 50 Duty Cycle Unit: Unit Raw Counts Auto Start: False GTIOCA Output Enabled: False GTIOCA Stop Level: Pin Level Low GTIOCB Output Enabled: False GTIOCB Stop Level: Pin Level Low Callback: touch_panel_callback Interrupt Priority: Priority 10 (CM4: valid, CM0+: invalid) Thread "QSPI Thread" Symbol: qspi_thread Name: QSPI Thread Stack size (bytes): 8192 Priority: 11 Auto start: Enabled Time slicing interval (ticks): 1 Instance "g_qspi QSPI Driver on QSPI" Name: g_qspi Object "g_qspi_cmd_queue Queue" Name: QSPI CMD Queue Symbol: g_qspi_cmd_queue Message Size (Words): 5 Queue Size (Bytes): 400 Thread "LED Thread" Symbol: led_thread Name: LED Thread Stack size (bytes): 1024 Priority: 1 Auto start: Enabled Time slicing interval (ticks): 1 Instance "g_timer0 Timer Driver on r_gpt" Name: g_timer0 Channel: 0 Mode: Periodic Period Value: 100 Period Unit: Milliseconds Duty Cycle Value: 50 Duty Cycle Unit: Unit Raw Counts Auto Start: True GTIOCA Output Enabled: False GTIOCA Stop Level: Pin Level Low GTIOCB Output Enabled: False GTIOCB Stop Level: Pin Level Low Callback: TimerCallback0 Interrupt Priority: Priority 10 (CM4: valid, CM0+: invalid) Instance "g_timer1 Timer Driver on r_gpt" Name: g_timer1 Channel: 1 Mode: Periodic Period Value: 500 Period Unit: Milliseconds Duty Cycle Value: 50 Duty Cycle Unit: Unit Raw Counts Auto Start: True GTIOCA Output Enabled: False GTIOCA Stop Level: Pin Level Low GTIOCB Output Enabled: False GTIOCB Stop Level: Pin Level Low Callback: TimerCallback1 Interrupt Priority: Priority 10 (CM4: valid, CM0+: invalid) Instance "g_timer3 Timer Driver on r_gpt" Name: g_timer3 Channel: 3 Mode: Periodic Period Value: 5000 Period Unit: Milliseconds Duty Cycle Value: 50 Duty Cycle Unit: Unit Raw Counts Auto Start: True GTIOCA Output Enabled: False GTIOCA Stop Level: Pin Level Low GTIOCB Output Enabled: False GTIOCB Stop Level: Pin Level Low Callback: TimerCallback3 Interrupt Priority: Priority 10 (CM4: valid, CM0+: invalid) Instance "g_timer4 Timer Driver on r_gpt" Name: g_timer4 Channel: 4 Mode: Periodic Period Value: 2000 Period Unit: Milliseconds Duty Cycle Value: 50 Duty Cycle Unit: Unit Raw Counts Auto Start: True GTIOCA Output Enabled: False GTIOCA Stop Level: Pin Level Low GTIOCB Output Enabled: False GTIOCB Stop Level: Pin Level Low Callback: TimerCallback4 Interrupt Priority: Priority 10 (CM4: valid, CM0+: invalid) Object "g_led_cmd_queue Queue" Name: LED CMD Queue Symbol: g_led_cmd_queue Message Size (Words): 2 Queue Size (Bytes): 200 Thread "ExInterrupt Thread" Symbol: ExInterrupt_thread Name: ExInterrupt Thread Stack size (bytes): 1024 Priority: 1 Auto start: Enabled Time slicing interval (ticks): 1 Instance "g_external_irq11 External IRQ Driver on r_icu" Name: g_external_irq11 Channel: 11 Trigger: Falling Digital Filtering: Enabled Digital Filtering Sample Clock (Only valid when Digital Filtering is Enabled): PCLK / 64 Interrupt enabled after initialization: True Callback: external_irq_callback11 Interrupt Priority: Priority 10 (CM4: valid, CM0+: invalid) Instance "g_external_irq13 External IRQ Driver on r_icu" Name: g_external_irq13 Channel: 13 Trigger: Falling Digital Filtering: Enabled Digital Filtering Sample Clock (Only valid when Digital Filtering is Enabled): PCLK / 64 Interrupt enabled after initialization: True Callback: external_irq_callback13 Interrupt Priority: Priority 10 (CM4: valid, CM0+: invalid) Instance "g_external_irq15 External IRQ Driver on r_icu" Name: g_external_irq15 Channel: 15 Trigger: Falling Digital Filtering: Enabled Digital Filtering Sample Clock (Only valid when Digital Filtering is Enabled): PCLK / 64 Interrupt enabled after initialization: True Callback: external_irq_callback15 Interrupt Priority: Priority 10 (CM4: valid, CM0+: invalid) Object "g_sw_queue Queue" Name: SW Queue Symbol: g_sw_queue Message Size (Words): 1 Queue Size (Bytes): 200 Thread "Touch Key Thread" Symbol: touch_key_thread Name: Touch Key Thread Stack size (bytes): 1024 Priority: 1 Auto start: Enabled Time slicing interval (ticks): 1 Instance "g_sf_touch_button0 Cap Touch Button Framework on sf_touch_ctsu_button" Name: g_sf_touch_button0 Button Configuration Structure Name (generated by Workbench): touch_buttons Callback: g_button_framework_user_callback Name of generated initialization function: sf_touch_button_init0 Auto Initialization: Enable Instance "g_sf_touch_ctsu0 Cap Touch Framework on sf_touch_ctsu" Name: g_sf_touch_ctsu0 Thread Priority: 3 Update Hz: 100 Callback: NULL Instance "g_ctsu0 CTSU Driver on r_ctsu" Name: g_ctsu0 CTSU configuration used: g_ctsu_config_self Callback: NULL Data Processing Option: Default Processing (Recommended) Write Interrupt Priority: Priority 7 (CM4: valid, CM0+: invalid) Read Interrupt Priority: Priority 7 (CM4: valid, CM0+: invalid) End Interrupt Priority: Priority 7 (CM4: valid, CM0+: invalid) Instance "g_transfer0 Transfer Driver on r_dtc Event CTSU END" Name: g_transfer0 Mode: Block Transfer Size: 2 Bytes Destination Address Mode: Incremented Source Address Mode: Incremented Repeat Area (Unused in Normal Mode): Source Interrupt Frequency: After all transfers have completed Destination Pointer: NULL Source Pointer: NULL Number of Transfers: 1 Number of Blocks (Valid only in Block Mode): 1 Activation Source (Must enable IRQ): Event CTSU END Auto Enable: False Callback (Only valid with Software start): NULL ELC Software Event Interrupt Priority: Disabled Instance "g_touch_key_timer Timer Driver on r_gpt" Name: g_touch_key_timer Channel: 6 Mode: Periodic Period Value: 20 Period Unit: Milliseconds Duty Cycle Value: 50 Duty Cycle Unit: Unit Raw Counts Auto Start: True GTIOCA Output Enabled: False GTIOCA Stop Level: Pin Level Low GTIOCB Output Enabled: False GTIOCB Stop Level: Pin Level Low Callback: touch_key_callback Interrupt Priority: Priority 10 (CM4: valid, CM0+: invalid) Object "g_touch_key_cmd_queue Queue" Name: TOUCH KEY Queue Symbol: g_touch_key_cmd_queue Message Size (Words): 1 Queue Size (Bytes): 200 Thread "HMI LCD Thread" Symbol: lcd_thread Name: HMI LCD Thread Stack size (bytes): 1024 Priority: 2 Auto start: Disabled Time slicing interval (ticks): 1 Instance "g_pwm_backlight Timer Driver on r_gpt" Name: g_pwm_backlight Channel: 2 Mode: PWM Period Value: 10 Period Unit: Milliseconds Duty Cycle Value: 50 Duty Cycle Unit: Unit Percent Auto Start: True GTIOCA Output Enabled: False GTIOCA Stop Level: Pin Level Low GTIOCB Output Enabled: True GTIOCB Stop Level: Pin Level Low Callback: NULL Interrupt Priority: Disabled Instance "GUIX on gx" Instance "g_sf_el_gx GUIX Port on sf_el_gx" Name: g_sf_el_gx Display Driver Configuration Inheritance: Inherit Graphics Screen 1 Name of User Callback function: NULL Screen Rotation Angle(Clockwise): 0 GUIX Canvas Buffer (required if rotation angle is not zero): Not used Size of JPEG Work Buffer (valid if JPEG hardware acceleration enabled): 768000 Memory section for GUIX Canvas Buffer: sdram Memory section for JPEG Work Buffer: sdram Instance "g_display Display Driver on r_glcd" Name: g_display Name of display callback function to be defined by user: NULL Input - Panel clock source select: Internal clock(GLCDCLK) Input - Graphics screen1: Used Input - Graphics screen1 frame buffer name: fb_background Input - Number of Graphics screen1 frame buffer: 2 Input - Section where Graphics screen1 frame buffer allocated: sdram Input - Graphics screen1 input horizontal size: 800 Input - Graphics screen1 input vertical size: 480 Input - Graphics screen1 input horizontal stride(not bytes but pixels): 800 Input - Graphics screen1 input format: 16bits RGB565 Input - Graphics screen1 input line descending: Not used Input - Graphics screen1 input lines repeat: Off Input - Graphics screen1 input lines repeat times: 0 Input - Graphics screen1 layer coordinate X: 0 Input - Graphics screen1 layer coordinate Y: 0 Input - Graphics screen1 layer background color alpha: 255 Input - Graphics screen1 layer background color Red: 255 Input - Graphics screen1 layer background color Green: 255 Input - Graphics screen1 layer background color Blue: 255 Input - Graphics screen1 layer fading control: None Input - Graphics screen1 layer fade speed: 0 Input - Graphics screen2: Not used Input - Graphics screen2 frame buffer name: fb_foreground Input - Number of Graphics screen2 frame buffer: 2 Input - Section where Graphics screen2 frame buffer allocated: sdram Input - Graphics screen2 input horizontal size: 800 Input - Graphics screen2 input vertical size: 480 Input - Graphics screen2 input horizontal stride(not bytes but pixels): 800 Input - Graphics screen2 input format: 16bits RGB565 Input - Graphics screen2 line descending: Off Input - Graphics screen2 input lines repeat: Off Input - Graphics screen2 input lines repeat times: 0 Input - Graphics screen2 layer coordinate X: 0 Input - Graphics screen2 layer coordinate Y: 0 Input - Graphics screen2 layer background color alpha: 255 Input - Graphics screen2 layer background color Red: 255 Input - Graphics screen2 layer background color Green: 255 Input - Graphics screen2 layer background color Blue: 255 Input - Graphics screen2 layer fading control: None Input - Graphics screen2 layer fade speed: 0 Output - Horizontal total cycles: 1024 Output - Horizontal active video cycles: 800 Output - Horizontal back porch cycles: 46 Output - Horizontal sync signal cycles: 20 Output - Horizontal sync signal polarity: Low active Output - Vertical total lines: 525 Output - Vertical active video lines: 480 Output - Vertical back porch lines: 23 Output - Vertical sync signal lines: 10 Output - Vertical sync signal polarity: Low active Output - Format: 24bits RGB888 Output - Endian: Little endian Output - Color order: BGR Output - Data Enable Signal Polarity: High active Output - Sync edge: Rising edge Output - Background color alpha channel: 255 Output - Background color R channel: 0 Output - Background color G channel: 0 Output - Background color B channel: 0 CLUT: Not used CLUT - CLUT buffer size: 256 TCON - Hsync pin select: LCD_TCON0 TCON - Vsync pin select: LCD_TCON1 TCON - DataEnable pin select: LCD_TCON2 TCON - Panel clock division ratio: 1/16 Color correction - Brightness: Off Color correction - Brightness R channel: 512 Color correction - Brightness G channel: 512 Color correction - Brightness B channel: 512 Color correction - Contrast: Off Color correction - Contrast(gain) R channel: 128 Color correction - Contrast(gain) G channel: 128 Color correction - Contrast(gain) B channel: 128 Color correction - Gamma correction(Red): Off Color correction - Gamma gain R[0]: 0 Color correction - Gamma gain R[1]: 0 Color correction - Gamma gain R[2]: 0 Color correction - Gamma gain R[3]: 0 Color correction - Gamma gain R[4]: 0 Color correction - Gamma gain R[5]: 0 Color correction - Gamma gain R[6]: 0 Color correction - Gamma gain R[7]: 0 Color correction - Gamma gain R[8]: 0 Color correction - Gamma gain R[9]: 0 Color correction - Gamma gain R[10]: 0 Color correction - Gamma gain R[11]: 0 Color correction - Gamma gain R[12]: 0 Color correction - Gamma gain R[13]: 0 Color correction - Gamma gain R[14]: 0 Color correction - Gamma gain R[15]: 0 Color correction - Gamma threshold R[0]: 0 Color correction - Gamma threshold R[1]: 0 Color correction - Gamma threshold R[2]: 0 Color correction - Gamma threshold R[3]: 0 Color correction - Gamma threshold R[4]: 0 Color correction - Gamma threshold R[5]: 0 Color correction - Gamma threshold R[6]: 0 Color correction - Gamma threshold R[7]: 0 Color correction - Gamma threshold R[8]: 0 Color correction - Gamma threshold R[9]: 0 Color correction - Gamma threshold R[10]: 0 Color correction - Gamma threshold R[11]: 0 Color correction - Gamma threshold R[12]: 0 Color correction - Gamma threshold R[13]: 0 Color correction - Gamma threshold R[14]: 0 Color correction - Gamma threshold R[15]: 0 Color correction - Gamma correction(Green): Off Color correction - Gamma gain G[0]: 0 Color correction - Gamma gain G[1]: 0 Color correction - Gamma gain G[2]: 0 Color correction - Gamma gain G[3]: 0 Color correction - Gamma gain G[4]: 0 Color correction - Gamma gain G[5]: 0 Color correction - Gamma gain G[6]: 0 Color correction - Gamma gain G[7]: 0 Color correction - Gamma gain G[8]: 0 Color correction - Gamma gain G[9]: 0 Color correction - Gamma gain G[10]: 0 Color correction - Gamma gain G[11]: 0 Color correction - Gamma gain G[12]: 0 Color correction - Gamma gain G[13]: 0 Color correction - Gamma gain G[14]: 0 Color correction - Gamma gain G[15]: 0 Color correction - Gamma threshold G[0]: 0 Color correction - Gamma threshold G[1]: 0 Color correction - Gamma threshold G[2]: 0 Color correction - Gamma threshold G[3]: 0 Color correction - Gamma threshold G[4]: 0 Color correction - Gamma threshold G[5]: 0 Color correction - Gamma threshold G[6]: 0 Color correction - Gamma threshold G[7]: 0 Color correction - Gamma threshold G[8]: 0 Color correction - Gamma threshold G[9]: 0 Color correction - Gamma threshold G[10]: 0 Color correction - Gamma threshold G[11]: 0 Color correction - Gamma threshold G[12]: 0 Color correction - Gamma threshold G[13]: 0 Color correction - Gamma threshold G[14]: 0 Color correction - Gamma threshold G[15]: 0 Color correction - Gamma correction(Blue): Off Color correction - Gamma gain B[0]: 0 Color correction - Gamma gain B[1]: 0 Color correction - Gamma gain B[2]: 0 Color correction - Gamma gain B[3]: 0 Color correction - Gamma gain B[4]: 0 Color correction - Gamma gain B[5]: 0 Color correction - Gamma gain B[6]: 0 Color correction - Gamma gain B[7]: 0 Color correction - Gamma gain B[8]: 0 Color correction - Gamma gain B[9]: 0 Color correction - Gamma gain B[10]: 0 Color correction - Gamma gain B[11]: 0 Color correction - Gamma gain B[12]: 0 Color correction - Gamma gain B[13]: 0 Color correction - Gamma gain B[14]: 0 Color correction - Gamma gain B[15]: 0 Color correction - Gamma threshold B[0]: 0 Color correction - Gamma threshold B[1]: 0 Color correction - Gamma threshold B[2]: 0 Color correction - Gamma threshold B[3]: 0 Color correction - Gamma threshold B[4]: 0 Color correction - Gamma threshold B[5]: 0 Color correction - Gamma threshold B[6]: 0 Color correction - Gamma threshold B[7]: 0 Color correction - Gamma threshold B[8]: 0 Color correction - Gamma threshold B[9]: 0 Color correction - Gamma threshold B[10]: 0 Color correction - Gamma threshold B[11]: 0 Color correction - Gamma threshold B[12]: 0 Color correction - Gamma threshold B[13]: 0 Color correction - Gamma threshold B[14]: 0 Color correction - Gamma threshold B[15]: 0 Dithering: Off Dithering - Mode: Truncate Dithering - Pattern A: Pattern 11 Dithering - Pattern B: Pattern 11 Dithering - Pattern C: Pattern 11 Dithering - Pattern D: Pattern 11 Misc - Correction Process Order: Brightness and Contrast then Gamma Line Detect Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Underflow 1 Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Underflow 2 Interrupt Priority: Disabled Instance "g_sf_jpeg_decode JPEG Decode Framework on sf_jpeg_decode" Name: g_sf_jpeg_decode Instance "g_jpeg_decode JPEG Decode Driver on r_jpeg" Name: g_jpeg_decode Byte Order for Input Data Format: Normal byte order (1)(2)(3)(4)(5)(6)(7)(8) Byte Order for Output Data Format: Normal byte order (1)(2)(3)(4)(5)(6)(7)(8) Output Data Color Format: Pixel Data RGB565 format Alpha value to be applied to decoded pixel data(only valid for ARGB8888 format): 255 Name of user callback function: NULL Decompression Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Data Transfer Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Instance "D/AVE 2D Driver on dave2d" Instance "D/AVE 2D Port on sf_tes_2d_drw" Instance "g_sf_touch_panel_i2c0 Touch Panel Framework on sf_touch_panel_i2c" Name: g_sf_touch_panel_i2c0 Thread Priority: 3 Hsize Pixels: 800 Vsize Pixels: 480 Update Hz: 10 Reset Pin: IOPORT_PORT_07_PIN_11 Touch Event Class Instance Number: 0 Touch Coordinate Rotation Angle(Clockwise): 0 Name of generated initialization function: sf_touch_panel_i2c_init0 Auto Initialization: Enable Instance "g_sf_message Messaging Framework on sf_message" Name: g_sf_message Work memory size in bytes: 2048 Pointer to subscriber list array: p_subscriber_lists name of the block pool internally used in the messaging framework: sf_msg_blk_pool Name of generated initialization function: sf_message_init0 Auto Initialization: Enable Instance "g_i2c I2C Master Driver on r_sci_i2c" Name: g_i2c Channel: 7 Rate: Standard Slave Address : 0x4A Address Mode: 7-Bit SDA Output Delay (nano seconds): 300 Bit Rate Modulation Enable: Enable Callback: NULL Receive Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Transmit Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Transmit End Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Instance "g_transfer1 Transfer Driver on r_dtc Event SCI7 TXI" Name: g_transfer1 Mode: Normal Transfer Size: 1 Byte Destination Address Mode: Fixed Source Address Mode: Incremented Repeat Area (Unused in Normal Mode): Source Interrupt Frequency: After all transfers have completed Destination Pointer: NULL Source Pointer: NULL Number of Transfers: 0 Number of Blocks (Valid only in Block Mode): 0 Activation Source (Must enable IRQ): Event SCI7 TXI Auto Enable: False Callback (Only valid with Software start): NULL ELC Software Event Interrupt Priority: Disabled Instance "g_transfer2 Transfer Driver on r_dtc Event SCI7 RXI" Name: g_transfer2 Mode: Normal Transfer Size: 1 Byte Destination Address Mode: Incremented Source Address Mode: Fixed Repeat Area (Unused in Normal Mode): Destination Interrupt Frequency: After all transfers have completed Destination Pointer: NULL Source Pointer: NULL Number of Transfers: 0 Number of Blocks (Valid only in Block Mode): 0 Activation Source (Must enable IRQ): Event SCI7 RXI Auto Enable: False Callback (Only valid with Software start): NULL ELC Software Event Interrupt Priority: Disabled Instance "g_sf_external_irq0 External IRQ Framework on sf_external_irq" Name: g_sf_external_irq0 Event: Semaphore Put Instance "g_external_irq0 External IRQ Driver on r_icu" Name: g_external_irq0 Channel: 7 Trigger: Falling Digital Filtering: Enabled Digital Filtering Sample Clock (Only valid when Digital Filtering is Enabled): PCLK / 64 Interrupt enabled after initialization: True Callback: NULL Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Instance "Touch Panel Driver on touch_panel_tsc2007" Name: g_sf_touch_panel_i2c_chip_tsc2007 Thread "UART Thread" Symbol: uart_thread Name: UART Thread Stack size (bytes): 8192 Priority: 1 Auto start: Enabled Time slicing interval (ticks): 1 Instance "g_sf_comms0 Communications Framework on sf_uart_comms" Name: g_sf_comms0 Name of generated initialization function: sf_comms_init0 Auto Initialization: Enable Instance "g_uart0 UART Driver on r_sci_uart" Name: g_uart0 Channel: 9 Baud Rate: 460800 Data Bits: 8bits Parity: None Stop Bits: 1bit CTS/RTS Selection: RTS (CTS is disabled) Name of UART callback function to be defined by user: NULL Name of UART callback function for the RTS external pin control to be defined by user: NULL Clock Source: Internal Clock Baudrate Clock Output from SCK pin: Disable Start bit detection: Falling Edge Noise Cancel: Disable Bit Rate Modulation Enable: Enable Receive FIFO Trigger Level: Max Receive Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Transmit Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Transmit End Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Error Interrupt Priority: Priority 3 (CM4: valid, CM0+: lowest - not valid if using ThreadX) Object "g_uart_sw_queue Queue" Name: UART SW Queue Symbol: g_uart_sw_queue Message Size (Words): 1 Queue Size (Bytes): 200 Object "g_uart_touch_key_queue Queue" Name: UART TOUCH KEY Queue Symbol: g_uart_touch_key_queue Message Size (Words): 1 Queue Size (Bytes): 200 Thread "Ethernet Thread" Symbol: ethernet_thread Name: Ethernet Thread Stack size (bytes): 8192 Priority: 10 Auto start: Enabled Time slicing interval (ticks): 1 Instance "dhcp_0 NetX Duo DHCP IPv4 Client" Name: dhcp_0 Name of generated initialization function: dhcp_client_init0 Auto Initialization: Enable Instance "ip_0 NetX Duo IP Instance" Name: ip_0 IPv4 Address (use commas for separation): 0,0,0,0 Subnet Mask (use commas for separation): 255,255,255,0 IPv6 Global Address (use commas for separation): 0x2001,0x0,0x0,0x0,0x0,0x0,0x0,0x1 IPv6 Link Local Address (use commas for separation , All zeros means use MAC address): 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 IP Helper Thread Stack Size (bytes): 4096 IP Helper Thread Priority: 3 ARP: Enable ARP Cache Size (bytes): 512 Reverse ARP: Disable TCP: Enable UDP: Enable ICMP: Enable IGMP: Enable IP fragmentation: Disable Name of generated initialization function: ip_init0 Auto Initialization: Enable Instance "NetX Duo Common on nxd" Name of generated initialization function: nx_common_init0 Auto Initialization: Enable Instance "pool_0 NetX Duo Packet Pool Instance" Name: pool_0 Packet Size (bytes): 2048 Number of Packets in Pool: 100 Name of generated initialization function: packet_pool_init0 Auto Initialization: Enable Instance "NetX Duo Common on nxd" Name of generated initialization function: nx_common_init0 Auto Initialization: Enable Instance "g_sf_el_nx NetX Port ETHER on sf_el_nx" Name: g_sf_el_nx Channel: 1 Callback: NULL Instance "NetX Duo DHCP IPv4 Common" Messaging Subscriber "HMI LCD Thread" 0 0 Event Class "Touch"